Dixon ZTR 5502 Specifiche

Page 7 SEAT ASSEMBLY INSTRUCTIONS 1. Assemble seat as shown in picture. Do not fully tighten the bolts which secure left and right arm rest brackets

Page 8 UPPER CONTROL LEVER INSTALLATION 1. Raise rear body cover to fully open position. 2. Install flat washer on right hand swivel plate weldmen

MOWER DECK INSTALLATION 1. To remove front body from chassis, disconnect headlights and remove acorn hut in middle of body. 2. Install rear hanger r

Page 10 MOWER DECK LEVELING PROCEDURE Leveling Principals: A. There are a total of (4) threaded adjusters which will control the attitude or pitch of

Page 11 FINAL PREPARATION 1. Remove battery from chassis. 2. Fill each cell with electrolyte (acid) to ring at bottom of fill cap. 3. Allow battery

Page 12 OPERATION INSTRUCTIONS The safe and successful operation of the Model 502 will depend upon the operator having the correct knowledge of all co

Page 13 OPERATION INSTRUCTIONS (continued) THROTTLE CONTROL LEVER: Controls engine speed. (Engine should be operated at full throttle when use.d in a

Page 14 CARE AND MAINTENANCE - MODEL 502 This portion of the Model 502 owners manual deals with normal service items which can be performed by the own

Page 15 CARE AND MAINTENANCE - MODEL 502 MOWER DECK SERVICE: CUTTER BLADE REMOVAL - BELT TENSION. "CAUTION" The removal of the cutter blades

Page 16 CARE AND MAINTENANCE - MODEL 502 DRIVE SYSTEM ADJUSTMENTS: Hydrostat Chains - Belts - Cable - Controls Refer to the diagrams on the followin

INDEX 1. SAFETY 2. WARRANTY POLICY 3. SPECIFICATIONS 4. SET UP AND SERVICE 5. OPERATION INSTRUCTIONS 6. CARE AND MAINTENANCE 7. TROUBLE SHO

(1) HYDROSTAT MOUNTING BOLTS (2) THREADED ADJUSTERS TO TENSION CHAINS Page 17

(1) ADJUSTMENT POINTS FOR T-BOX BELT TENSION Page 18

(1) Forward lever stop adjustment Page 19

Page 20 CARE AND MAINTENANCE - MODEL 502 LUBRICATION: CHASSIS AND MOWER DECK: Number of grease zerks used (2) LOCATIONS: (1) each front wheel caste

Page 21 CARE AND MAINTENANCE - MODEL 502 CLEANING THE MOWER: A clean machine is a source of pride to the owner. However, cleaning by use of high press

MOWER CUT QUALITY: There are many variables that can effect the cut quality of any multi blade mower. Type and condition of grass, ground speed, b

DRIVE SYSTEM: SITUATION Mower pulls to one side or the other Loss of drive power on one side or the other Loss of power on both wheels after bei

ELECTRICAL SYSTEM: SITUATION Starter will not turn engine over Starter will not turn engine over Battery discharge Battery discharge Battery disch

DECK ASSEMBLY (MODEL 5O2)

Body Assembly (Model 502)

IMPORTANT - READ CAREFULLY The Dixon ZTR Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is n

T-BOX AND HYDROSTATS ASSEMBLY (MODEL 502)

CHASSIS ASSEMBLY (MODEL 502)

FUEL & HYDRAULICS TANKS & FITTINGS ASSEMBLY (MODEL 502) 1 a1C at

WIRING ASSEMBLY (MODEL 502) >t Q) •

1300 Belt 36" Mower Drive 1384 Tank Mount Bracket (Short) 1385 Tank Mount Bracket (Long) 1469 LH Slide Angle 1470 RH Slide Angle 1471 Sea

1991 ZTR 502 Parts List 3601 Load Mount 3602 Spacer Tube 3603 ISO Mount Insert 3617 Decal - DIXON 3635 Tee-Fuel Line 3644 Fuel Line 5 1/2"

1991ZTR 502 Parts List 5615 Connector/Elbow Assembly 5623 Electric Clutch 5624 Tank Cap 5627 Left Fan 5628 Right Fan 6011 Mower Deck Bearing 610

SAFETY RIDING LAUNMOVJERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY. The following examples are the most common ca

SAFETY Page 2 SAFETY REMINDERS: READ CAREFULLY BEFORE OPERATION 1. Wear appropriate, safe clothing when mowing - close fitting jeans or slacks and h

Page 3 SAFETY REMINDERS: (continued) 16. Use care when pulling loads or using heavy equipment. A. Use only approved drawbar hitch points. B. Limit l

Page 5 SPECIFICATIONS Chassis: 11 GA - rectangular tube. Body: Two piece - made of DR acrylic reinforced with fiberglass, color fast, scratch and im

SET UP AND SERVICE 1. Seat assembly instructions. 2. Upper control lever installation. 3. Mower deck installation. 4. Deck leveling procedure. 5.